6.8. jules_snow.nml

This file sets the snow options and parameters. It contains one namelist called JULES_SNOW.

6.8.1. JULES_SNOW namelist members

HCTN30 refers to Hadley Centre technical note 30, available from the Met Office Library.

JULES_SNOW::nsmax

Type:integer Permitted:>= 0 Default:0

Maximum possible number of snow layers.

0

A composite soil/snow layer is used. This value gives the behaviour found in JULES2.0 and earlier.

> 0

The state of up to nsmax separate snow layers is modelled. Values of nsmax = 3 or more are recommended.

JULES_SNOW::l_snowdep_surf

Type:logical Default:F

TRUE

Use equivalent canopy snow depth for surface calculations on tiles with a snow canopy.

FALSE

No effect.

JULES_SNOW::frac_snow_subl_melt

Type:integer Permitted:0 or 1 Default:0

Switch for use of snow-cover fraction in the calculation of sublimation and melting.

0. Off
1. On

JULES_SNOW::dzsnow

Type:real(nsmax) Default:None

Prescribed thickness of each snow layer (m).

Only used if nsmax > 0.

The interpretation of dzsnow is slightly complicated and an example of the evolution of the snow layers is given below.

dzsnow gives the thickness of each layer when it is not the bottom layer.

For the top layer, the minimum thickness is dzsnow(1) and the maximum thickness is 2 * dzsnow(1). For all other layers iz, the minimum thickness is dzsnow(iz - 1), i.e. the given thickness of the previous layer, and the maximum thickness is 2 * dzsnow(iz), i.e. twice the layer dzsnow value, except for the last possible layer (nsmax) which has no upper limit.

As a snowpack deepens, the bottom layer (closest to the soil; label this as layer b) thickens until it reaches its maximum allowed thickness, at which point it will split into a layer of depth dzsnow(b) and a new bottom layer b + 1 is added to hold the remaining snow. If a layer becomes thinner than its value in dzsnow it is removed and the snow partitioned between the remaining layers. Whenever a layer splits or is removed, the properties of the layer (e.g. temperature) are allocated to the remaining layers.

Note that dzsnow(nsmax), the final thickness, is not used but a value must be input.

JULES_SNOW::cansnowpft

Type:logical(npft) Default:F

Flag indicating whether snow can be held under the canopy of each PFT.

Only used if can_model = 4.

The model of snow under the canopy is currently only suitable for coniferous trees.

TRUE

Snow can be held under the canopy.

FALSE

Snow cannot be held under the canopy.

Radiation parameters

JULES_SNOW::r0

Type:real Default:50.0

Grain size for fresh snow (μm).

Only used if l_snow_albedo = TRUE. See HCTN30 Eq.15.

JULES_SNOW::rmax

Type:real Default:2000.0

Maximum snow grain size (μm).

Only used if l_snow_albedo = TRUE. See HCTN30 p4.

JULES_SNOW::snow_ggr

Type:real(3) Default:0.6, 0.06, 0.23e6

Snow grain area growth rates (μm² s^-1).

Only used if l_snow_albedo = TRUE. See HCTN30 Eq.16.

The 3 values are for melting snow, cold fresh snow and cold aged snow respectively.

JULES_SNOW::amax

Type:real(2) Default:0.98, 0.7

Maximum albedo for fresh snow.

Only used if l_snow_albedo or l_elev_land_ice are true

Values 1 and 2 are for VIS and NIR wavebands respectively.

JULES_SNOW::aicemax

Type:real(2) Default:0.78, 0.36

Maximum albedo for bare ice

Only used if l_elev_land_ice = TRUE. See also rho_firn_albedo

Values 1 and 2 are for VIS and NIR wavebands respectively.

JULES_SNOW::maskd

Type:real Default:50.0

Used in exponent of equation weighting snow-covered and snow-free albedo.

JULES_SNOW::dtland

Type:real Default:2.0

Degrees Celsius below zero at which snow albedo equals cold deep snow albedo.

Only used if l_snow_albedo = FALSE. This is 2.0 in HCTN30 Eq4.

JULES_SNOW::kland_numerator

Type:real Default:0.3

Used in snow-ageing effect on albedo.

Only used if l_snow_albedo = FALSE.

Must not be zero.

kland is computed by dividing this value by dtland - see HCTN30 Eq4.

JULES_SNOW::can_clump

Type:real(npft) Default:MDI

Clumping parameter for snow on the canopy in calculation of albedo.

Only used if can_model = 4, cansnowpft = TRUE on that tile and l_embedded_snow = TRUE.

JULES_SNOW::n_lai_exposed

Type:real(npft) Default:MDI

LAI distribution parameter for calculation of snow albedo.

Only used if l_embedded_snow = TRUE.

JULES_SNOW::lai_alb_lim_sn

Type:real(npft) Default:MDI

Minimum LAI in calculation of albedo in the presence of snow.

Other snow parameters

JULES_SNOW::rho_snow_const

Type:real Default:250.0

Constant density of lying snow (kg m^-3).

This value is used if nsmax = 0, in which case all snow is modelled as a single layer of constant density.

JULES_SNOW::rho_snow_fresh

Type:real Default:100.0

Density of fresh snow (kg m^-3).

This value is only used if nsmax > 0.

JULES_SNOW::rho_firn_albedo

Type:real Default:550.0

If l_elev_land_ice = TRUE, this is the threshold density (as measured over the ~top 10cm, depending on how the dzsnow layers are specified) at which the grain-size calculation of prognostic snow albedo will switch to one dependent on the surface density of the snowpack. Albedo is linearly scaled between amax for rho_snow_const and aicemax for rho_ice=917 kg/m^3.

JULES_SNOW::snow_hcon

Type:real Default:0.265

Thermal conductivity of lying snow (W m^-1 K^-1).

See HCTN30 Eq.42.

JULES_SNOW::snow_hcap

Type:real Default:0.63e6

Thermal capacity of lying snow (J K^-1 m^-3).

JULES_SNOW::snowliqcap

Type:real Default:0.05

Liquid water holding capacity of lying snow, as a fraction of snow mass.

Only used if nsmax > 0.

JULES_SNOW::snowinterceptfact

Type:real Default:0.7

Constant in relationship between mass of intercepted snow and snowfall rate.

Only used if can_model = 4.

JULES_SNOW::snowloadlai

Type:real Default:4.4

Ratio of maximum canopy snow load to leaf area index (kg m^-2).

Only used if can_model = 4.

JULES_SNOW::snowunloadfact

Type:real Default:0.4

Constant in relationship between canopy snow unloading and canopy snow melt rate.

Only used if can_model = 4.

JULES_SNOW::unload_rate_cnst

Type:real(npft) Default:MDI

Constant term in the background unloading rate for snow on the canopy.

Only used if can_model = 4 and cansnowpft = TRUE on that tile.

JULES_SNOW::unload_rate_u

Type:real(npft) Default:MDI

Term proportional to wind speed in unloading rate for snow on the canopy.

Only used if can_model = 4 and cansnowpft = TRUE on that tile.

JULES_SNOW::i_snow_cond_parm

Type:integer Permitted:0 or 1 Default:MDI

Scheme used to calculate the conductivity of snow

Only used if nsmax > 0.

JULES_SNOW::l_et_metamorph

Type:logical Default:F

TRUE

Include the effect of thermal metamorphism on the snow density.

FALSE

No effect.

JULES_SNOW::l_snow_infilt

Type:logical Default:F

TRUE

Pass rainfall and melting from the canopy to the snowpack as infiltration.

FALSE

No effect.

JULES_SNOW::l_snow_nocan_hc

Type:logical Default:F

TRUE

Do not include the canopy heat capacity in the surface energy balance at the top of the snow pack on tiles without a canopy snow model.

FALSE

The canopy heat capacity is include in the surface energy balance at the top of the snow pack.

JULES_SNOW::a_snow_et

Type:real Default:MDI

Constant in parametrization of thermal metamorphism.

Only used if l_et_metamorph = TRUE.

JULES_SNOW::b_snow_et

Type:real Default:MDI

Constant in parametrization of thermal metamorphism.

Only used if l_et_metamorph = TRUE.

JULES_SNOW::c_snow_et

Type:real Default:MDI

Constant in parametrization of thermal metamorphism.

Only used if l_et_metamorph = TRUE.

JULES_SNOW::rho_snow_et_crit

Type:real Default:MDI

Critical density in parametrization of thermal metamorphism.

Only used if l_et_metamorph = TRUE.

6.8.2. Example of the evolution of snow layer thickness

The table below gives an example of how the number and thickness of snow layers varies with total snow depth for the case of nsmax = 3 and dzsnow = (0.1, 0.15, 0.2). Note that if the values given by the user for dzsnow are a decreasing series with dzsnow(i) <= 2 * dzsnow(i - 1), the algorithm will result in layers i and i + 1 being added at the same time. Don’t panic - this should not be a problem for the simulation.

Snow depth (m)	Number of layers	Layer thickness, uppermost layer first (m)	Comments
d < 0.1	0		While the depth of snow is less than dzsnow(1), the layer model is not active and snow and soil are combined in a composite layer.
0.1 <= d < 0.2	1	Total snow depth	The single layer grows until it is twice as thick as dzsnow(1).
0.2 <= d < 0.4	2	0.1, remainder	Above 0.2m, the single layer splits into a top layer of 0.1m and the remaining snow in the bottom layer.
>= 0.4	3	0.1, 0.15, remainder	At 0.4m depth, layer 2 (which has grown to 0.3m thick, i.e. 2 * dzsnow(2)), splits into a layer of 0.15m and a new bottom layer holding the the remaining 0.15m. As all layers are now in use, any subsequent deepening of the pack is dealt with by increasing the thickness in this bottom layer.