3.5. Automatic upgrading and GUI using Rose

Rose is a collection of tools for managing the building and running of scientific applications.

See also

Please familiarise yourself with the Rose documentation before continuing with this section.

Note

This section assumes Rose is installed.

We will not be using Rose Bush or Rosie, so those components need not be installed.

It is not necessary to install Cylc, but some functionality will not be available. This will be noted as we go.

JULES uses Rose primarily to provide a graphical interface for configuring and running JULES, but also to allow automatic upgrading of JULES runs from one version to the next.

A Rose suite for JULES will normally contain two applications - an fcm_make application for building JULES and a jules application for configuring the namelists and running JULES.

3.5.1. Creating a Rose suite from existing namelists

To enable users to quickly transition to Rose and the extra functionality it provides, a tool is distributed with JULES that can convert existing namelists to a Rose suite.

To convert vn3.4 namelists to a vn4.0 Rose suite, run the following command in the directory containing the namelists:

$JULES_ROOT/bin/create_rose_app vn3.4 vn4.0

where $JULES_ROOT is the root directory of your JULES installation.

This will create a directory called rose-suite which contains a fully functional Rose suite.

3.5.2. Using Rose to upgrade existing namelists

It is not necessary to use Rose to configure and run JULES - Rose can be used just to upgrade existing namelists (at vn3.4 or later).

In order to use Rose to upgrade existing namelists from vn3.4 to vn4.0, just execute the following commands in the directory containing your namelists:

# Creates a Rose suite at rose-suite
$JULES_ROOT/bin/create_rose_app vn3.4 vn4.0

# Remove the current namelists
rm -rf *.nml

# Use Rose to generate the new namelists
rose app-run -i -C rose-suite/app/jules

# Remove the Rose suite and other generated files
rm -rf rose-suite .rose-config_processors-file.db rose-app-run.conf

3.5.3. Upgrading an existing JULES Rose suite

Upgrading an existing JULES Rose suite is even more simple than upgrading the namelist files directly. To see the versions it is possible to upgrade to, run the command:

rose app-upgrade -M $JULES_ROOT/rose-meta -C /path/to/rose/suite/app/jules --all-versions

To then upgrade to one of those versions, the command is:

rose app-upgrade -M $JULES_ROOT/rose-meta -C /path/to/rose/suite/app/jules <version>

3.5.4. Configuring JULES with a graphical interface

Using a Rose suite to run JULES has the advantage that it can be configured graphically using Rose Config Edit.

To launch the graphical editor, the following command is used:

# To edit the whole suite, including build configuration
rose config-edit -M $JULES_ROOT/rose-meta -C /path/to/rose/suite &

# To edit just the namelists
rose config-edit -M $JULES_ROOT/rose-meta -C /path/to/rose/suite/app/jules &

where $JULES_ROOT is the root directory of your JULES installation. For more information on using the config editor, see the Rose documentation

Clicking on a variable name in the editor opens the corresponding page in this documentation.

3.5.5. Running a JULES Rose suite

3.5.5.1. Without Cylc

To run JULES from a Rose suite without Cylc, we just use Rose to generate the namelists. JULES is then built and run as normal - see Building and running JULES.

To generate namelists in the current directory from a Rose suite at /path/to/rose/suite, use the following command:

rose app-run -i -C /path/to/rose/suite/app/jules

3.5.5.2. With Cylc

Warning

This requires Cylc to be installed and configured.

Once a JULES Rose suite has been suitably configured using the graphical editor, it can be run using the following command:

rose suite-run -C /path/to/rose/suite

This will set the suite running, and will launch the Cylc GUI to allow you to see the status of your suite as it runs. The GUI also allows you to view log files etc. - these can be useful when a job fails!